/resources/image/template/step.png BGA


The Ball Grid Array (BGA) is a very different package to those using pins, such as the quad flat pack. Is a type of surface-mount packaging (a chip carrier) used for integrated circuits? BGA packages are used to permanently mount devices such as microprocessors. A BGA can provide more interconnection pins than can be put on a dual in-line or flat package. The whole bottom surface of the device can be used, instead of just the perimeter. The leads are also on average shorter than with a perimeter-only type, leading to better performance at high speeds. The pins of the BGA package are arranged in a grid pattern and this gives rise to the name. In addition to this, rather than having the more traditional wire pins for the connections, pads with balls of solder are used instead. On the printed circuit board, PCB, onto which the BGA components are to be fitted there, is a matching set of copper pads to provide the required connectivity.

BGA packages offer many advantages over their quad flat pack rivals and as a result they are being used increasingly for the manufacture of electronic circuits:

  • Improved PCB design as a result of lower track density: Track densities around many packages such as the quad flat pack become very high because of the very close proximity of the pins. A BGA spreads the contacts out over the full area of the package greatly reducing the problem.
  • The BGA package is robust: Packages such as the quad flat pack have very fine pins, and these are easily damaged by even the most careful handling. It is almost impossible to repair them once the pins are bent owing to their very fine pitch. BGAs do not suffer from this as the connections are provided by pads with the BGA solder balls on them which are very difficult to damage.
  • Lower thermal resistance: BGAs offer a lower thermal resistance between the silicon chip itself than quad flat pack devices. This allows heat generated by the integrated circuit inside the package to be conducted out of the device onto the PCB faster and more effectively.
  • Improved high speed performance: As the conductors are on the underside of the chip carrier. This means that the leads within the chip are shorter. Accordingly unwanted lead inductance levels are lower, and in this way, Ball Grid Array devices are able to offer a higher level of performance than their QFP counterparts.

BGA solder process

One of the initial fears over the use of BGA components was their solderability and whether soldering BGA components could be made as reliable as soldering devises using more traditional forms of connection. As the pads are under the device and not visible it is necessary to ensure the correct process is used and it is fully optimized. Inspection and rework were also concerns.

Fortunately BGA solder techniques have proved to be very reliable, and once the process is set up correctly BGA solder reliability is normally higher than that for quad flat packs. This means that any BGA assembly tends to be more reliable. Its use is therefore now widespread in both mass production PCB assembly and also prototype PCB assembly where circuits are being developed.

For the BGA solder process, reflow techniques are used. The reason for this is that the whole assembly needs to be brought up to a temperature whereby the solder will melt underneath the BGA components themselves. This can only be achieved using reflow techniques.

For BGA soldering, the solder balls on the package have a very carefully controlled amount of solder, and when heated in the soldering process, the solder melts. Surface tension causes the molten solder to hold the package in the correct alignment with the circuit board, while the solder cools and solidifies. The composition of the solder alloy and the soldering temperature are carefully chosen so that the solder does not completely melt, but stays semi-liquid, allowing each ball to stay separate from its neighbors.

BGA solder joint inspection

BGA inspection is one area of the manufacturing process that has raised a considerable amount of interest since the introduction of the first BGA components. BGA inspection cannot be achieved in the normal way using straightforward optical techniques because, quite obviously, the solder joints are underneath the BGA components and they are not visible. This creates problems for BGA inspection. It also created a considerable degree of unease about the technology when it was first introduced and many manufacturers undertook tests to ensure that they were able to solder the BGA components satisfactorily. The main problem with soldering BGA components is that sufficient heat must be applied to ensure that all the balls in the grid melt sufficiently for every BGA solder joint to be satisfactorily made.

The solder joints cannot be fully tested by checking the electrical performance. While this form of test of the BGA solder process will reveal conductivity at that time, it does not give a full picture of how the BGA solder process has succeeded. It is possible that the joint may not be adequately made and that over time it will fail. For this the only satisfactory means of test is a form of BGA inspection using X-rays. This form of BGA inspection is able to look through the device at the soldered joint beneath. Fortunately, it is found that once the heat profile for the solder machine is set up correctly, the BGA components solder very well and few problems are encountered with the BGA solder process.

BGA rework

As might be anticipated, it is not easy to rework BGA assemblies unless the correct equipment is available. If a BGA component is suspected as being faulty, then it is possible to remove the device. This is achieved by locally heating the BGA component to melt the solder underneath it.

In the BGA rework process, the heating is often achieved in a specialized rework station. This comprises a jig fitted with infrared heater, a thermocouple to monitor the temperature and a vacuum device for lifting the package. Great care is needed to ensure that only the BGA is heated and removed. Other devices nearby need to be affected as little as possible otherwise they may be damaged.

BGA technology in general and in particular, the BGA soldering process has proved them to be very successful since they were first introduced. They are now an integral part of the PCB assembly process used in most companies for mass production and for prototype PCB assembly.

Sub Menu

Feb 1, 2019 10:35:33 AM

Jul 10, 2017 7:31:01 AM

Jun 30, 2017 5:45:40 AM

Jun 19, 2017 7:46:16 AM

Jun 19, 2017 5:29:38 AM

Copyright 2009 Geto Custom electronics applciations. All rights reserved. Contact us: info@geto.com.gr